River Publishers Series in Chemical, Environmental, and Energy Engineering
2 total works
Coiled Tubing and Other Stimulation Techniques
by Mohammed Ismail Iqbal and Shohaib Khan
Published 15 April 2019
Good engineers never stop looking for opportunities to improve the performance of their production systems. Performance enhancement methods are always carefully examined, and production data is analyzed in order to identify determining factors affecting performance.
The two main activities of the production engineer in the petroleum and related industries are reservoir stimulation and artificial lift. The classic solution to maximizing a well's productivity is to stimulate it. The basis for selecting stimulation candidates should be a review of the well's actual and theoretical IPR. Low permeability wells often need fracturing on initial completion. In low permeability zones, additional post stimulation production can be significant to the economics, however, the production engineer needs to make management aware of the true long term potential or else overly optimistic projections can easily be made.
The main purpose of stimulation is to enhance the property value by the faster delivery of the petroleum fluid and/or to increase ultimate economic recovery. The aim of reservoir stimulation is to bypass near-wellbore damage and return a well to its "natural" productivity / injectivity, to extend a conductive path deep into a formation and thus increase productivity beyond the natural level and to produce hydrocarbon from tight formation.
The importance of reservoir stimulation is increasing due to following reasons:
* Hydrocarbon fields in their mid-life
* Production in these fields are in declining trend
* The thrust area: Enhancement of production
Hence, to improve productivity of the well matrix stimulation and hydraulic fracturing are intended to remedy, or even improve, the natural connection of the wellbore with the reservoir, which could delay the need for artificial lift.
This book presents procedures taken in the Oil & Gas Industry for identifying well problems, and it suggests means of solving problems with the help of the Coil Tube unit which is used for improving well productivity and techniques like Acidizing and Hydraulic Fracturing.
The two main activities of the production engineer in the petroleum and related industries are reservoir stimulation and artificial lift. The classic solution to maximizing a well's productivity is to stimulate it. The basis for selecting stimulation candidates should be a review of the well's actual and theoretical IPR. Low permeability wells often need fracturing on initial completion. In low permeability zones, additional post stimulation production can be significant to the economics, however, the production engineer needs to make management aware of the true long term potential or else overly optimistic projections can easily be made.
The main purpose of stimulation is to enhance the property value by the faster delivery of the petroleum fluid and/or to increase ultimate economic recovery. The aim of reservoir stimulation is to bypass near-wellbore damage and return a well to its "natural" productivity / injectivity, to extend a conductive path deep into a formation and thus increase productivity beyond the natural level and to produce hydrocarbon from tight formation.
The importance of reservoir stimulation is increasing due to following reasons:
* Hydrocarbon fields in their mid-life
* Production in these fields are in declining trend
* The thrust area: Enhancement of production
Hence, to improve productivity of the well matrix stimulation and hydraulic fracturing are intended to remedy, or even improve, the natural connection of the wellbore with the reservoir, which could delay the need for artificial lift.
This book presents procedures taken in the Oil & Gas Industry for identifying well problems, and it suggests means of solving problems with the help of the Coil Tube unit which is used for improving well productivity and techniques like Acidizing and Hydraulic Fracturing.
Coil Tubing Unit for Oil Production and Remedial Measures
by Mohammed Ismail Iqbal
Published 20 December 2021
* Mechanical methods
* Chemical methods
* Combination methods
Description / back cover text:
Well activation is one of the most important aspects in the oil and gas industries and nitrogen gas is predominately used. The gas, being light, is sent down the producing reservoir which will enhance the production or improve the flow of crude oil. In addition to the methods used to increase production there are several problems like sand production and water production from the producing wells.
Sand production occurs when the destabilizing stresses at the formation face exceed the strength of the natural arching tendencies and/or grain-to-grain cementation strength. Ideally, during oil production, the formation should be porous, permeable and well consolidated through which hydrocarbons can easily flow into the production wells. But sometimes, especially during production from unconsolidated sandstone reservoirs, the produced hydrocarbons may also carry large amounts of sand into the well bore and sand entering production wells is one of the oldest problems faced by oil companies and one of the toughest to solve. These unconsolidated formations may not restrain grain movement, and produce sand along with the fluids especially at high rates.
Water production is also a problem that many reservoir or production engineers face in day-to-day life. As engineers we should be able to decide whether water control solutions should be applied or not. The excess production of water is caused by the depletion of the reservoir and simply sweeps away most of the oil that the reservoir can produce.
This book gives an information how well activation using nitrogen is carried out, and how sand control and water control issues can be resolved.
* Chemical methods
* Combination methods
Description / back cover text:
Well activation is one of the most important aspects in the oil and gas industries and nitrogen gas is predominately used. The gas, being light, is sent down the producing reservoir which will enhance the production or improve the flow of crude oil. In addition to the methods used to increase production there are several problems like sand production and water production from the producing wells.
Sand production occurs when the destabilizing stresses at the formation face exceed the strength of the natural arching tendencies and/or grain-to-grain cementation strength. Ideally, during oil production, the formation should be porous, permeable and well consolidated through which hydrocarbons can easily flow into the production wells. But sometimes, especially during production from unconsolidated sandstone reservoirs, the produced hydrocarbons may also carry large amounts of sand into the well bore and sand entering production wells is one of the oldest problems faced by oil companies and one of the toughest to solve. These unconsolidated formations may not restrain grain movement, and produce sand along with the fluids especially at high rates.
Water production is also a problem that many reservoir or production engineers face in day-to-day life. As engineers we should be able to decide whether water control solutions should be applied or not. The excess production of water is caused by the depletion of the reservoir and simply sweeps away most of the oil that the reservoir can produce.
This book gives an information how well activation using nitrogen is carried out, and how sand control and water control issues can be resolved.